HINGED-ARM AUTOMATION FOR SWING-TO GATES


Motor power supply 24 Vdc
Maximum gate weight 200 kg
Maximum opening angle 130°
Incorporated electronic programmer

BL824 SERIES

A complete automatic device for swing-to gates with one or two gate leaves, the system is made up of a Master unit and a Slave unit powering the second hinged gate. Particularly suited for installations with narrow columns that require the mounting base to be less than 150 mm in width and also for gates where the hinges are not aligned to the edge of the column and with gate leaves of up to 2 metres in length and 200 kg maximum weight. Installation is facilitated and the geared motor is well anchored by the special practical cast aluminium wall (or column) bracket predisposed for any type of fastening.

The compact and robust fastening bracket allows the automation to be fitted to very narrow columns. The extremely robust cast aluminium operator arms are fitted with joints for all applications and are able to drive hinged gates with different constructive characteristics.

The avant-garde electronic programmer (on board the master motor) features encoder-controlled gate positioning. Programming is self-learning. Repositioning takes place automatically whenever foreign objects get in the way of the gate as it is moving. The electronic control unit is completed by the anti-crush and “soft start” and “soft stop” functions.
The electronic programmer is factory fitted with a graphic LCD display (128 x 128 pixels) with backlighting in six different languages. The menu allows you to rapidly set the system parameters including: the sequential button mode, automatic reclosing, warning lamp pre-flashing, intermittent warning lamp activation, indicator light and photoelectric cell function setting and electric lock enable etc.
The master appliance is fitted with an RF module for remote control (system S449), a battery charger and buffer batteries which allow the gate to be manoeuvred even during blackouts. Manual release is carried out using the hexagonal key located inside the side panel.



Product DescriptionCode
  • Electromechanical unit with a 24 Vdc MOTOR

    Encoder controlled integral “master” unit
    fitted with an electronic programmer, radio receiver card,
    battery charger and NiMH batteries.
    Operator arm to be ordered separately.

    SELF-LOCKING MASTER AUTOMATION 200/BL824MCB

  • Electromechanical unit with a 24 Vdc MOTOR

    Encoder controlled ‘slave’ automation.


    Operator arm to be ordered separately.


     SELF-LOCKING SLAVE AUTOMATION  200/BL824S

  • Operational constraints:

    For gates with a maximum length of 2 m (2,5 m with a hinged arm

    and an electric lock), maximum weight 200 kg.


    For the electric locks turn to catalogue.

  • HINGED/STRAIGHT ARM DIMENSIONS

     STANDARD HINGED OPERATOR ARM  206/BL824ARM
     in spray-painted cast aluminium

     STRAIGHT ARM WITH SLIDING GUIDE  206/BL824DRM
    in spray-painted cast aluminium

     1000 MM GUIDE FOR SPECIAL OPENING REQUIREMENTS  206/BL3924GU2
    Supplied in lots of 2 pieces
     

  • 6-WIRE SPECIAL CONNECTING CABLE

     10 M CABLE  CABPC10
    (with end sleeves)

     100 m cable  CABPC100ST
    (supplied on a special spool)

  • KIT BATTERY CHARGER + NIMH BATTERIES

     KIT BATTERY CHARGER + NIMH BATTERIES  KBNiMH-3
    Allows the unit 200/BL824MCB to work during blackouts

HINGED/STRAIGHT ARM DIMENSIONS

TECHNICAL DATA

 OPERATOR ARM TECHNICAL SPECIFICATIONS

   
 Power supply
 Vdc  24
 Electrical input A  2
 Power input  W  50
 Duty cycle  %  70
 Opening time 90°  s  14 (12*)
 Maximum opening angle
 °  130
 Maximum torque
 Nm  270

 Protection grade

 IP  44
* using a straight operator arm
     

 ELECTRONIC PROGRAMMER TECHNICAL SPECIFICATIONS

   
 Power supply
 Vac  230
 
Electrical input
 A  1,2

 Maximum power yield

 W  250
 Power output for 1 or 2 motors:  W  60 + 60

 Class II device

 Cls  II
     

 INCORPORATED RECEIVER CARD

   
 Reception frequency S449  MHz  433.92
 Number of channels
 N°  4
 Number of functions  N°  6
 Number of stored codes
 N°  300


INSTALLATION EXAMPLE


LEGEND

1 Geared motor (left) 
2 Geared motor (right)
3 Internal photocells
4 External photocells
5 Warning lights 
6 Mechanical selector switch
7 Electric locking device 
8 External aerial
9 All pole circuit breaker
10 Mains cable 230 Vac
11 Channelling for Cardin connection cable CABPC10
12 Channelling route for low voltage wires
13 Lateral protective photocells

Attention: The drawing is purely indicative and is supplied as a working base from which to choose the Cardin electronic components making up the installation. This drawing therefore does not lay down any obligations regarding the execution of the installation.

HINGED-ARM AUTOMATION FOR SWING-TO GATES


Motor power supply 24 Vdc
Maximum gate weight 400 kg
Maximum opening angle 130°
Incorporated electronic programmer

BL3924 SERIES

A complete automatic device for large and medium size swing-to gates with one or two gate leaves, the system is made up of a Master unit and a Slave unit powering the second swing-to gate. Particularly suited for installations with large size columns where the hinges are not aligned to the edge of the column and with gate leaves of up to 3,5 metres in length and 400 kg maximum weight. Installation is facilitated and the geared motor is well anchored by the special cast aluminium wall (or column) bracket predisposed for any type of fastening. The robust fastening bracket allows the automation to be fitted to brick built columns. The extremely robust cast aluminium operator arms are fitted with joints for all applications and are able to drive hinged gates with different constructive characteristics.
The avant-garde electronic programmer (on board the master motor) features encoder-controlled gate positioning. Programming is self-learning. Repositioning takes place automatically whenever foreign objects get in the way of the gate as it is moving. The electronic control unit is completed by the anti-crush and “soft start” and “soft stop” functions.
The electronic programmer is factory fitted with a display, which indicates all the programming stages and events that occur during operation. The Master electronic appliance is fitted with an RF module for remote control (system S449) and comes complete with a battery charger and buffer batteries allowing emergency manoeuvring even during blackouts. Manual release is carried out using the supplied hexagonal key after first unlocking and removing the covering cap.



Product DescriptionCode
  • ELECTROMECHANICAL UNIT WITH A 24 Vdc MOTOR

    Encoder controlled integral “master” unit
    fitted with an electronic programmer, a radio receiver card,
    battery charger and NiMH batteries.

    Operator arm to be ordered separately.

     SELF-LOCKING MASTER AUTOMATION  200/BL3924CSB
     REVERSIBLE MASTER AUTOMATION   200/BL3924CRB

  • ELECTROMECHANICAL UNIT WITH A 24 Vdc MOTOR

    Encoder controlled integral “master”
    unit fitted with an electronic programmer, a radio receiver card,
    battery charger and NiMH batteries.

    Operator arm to be ordered separately.

     SELF-LOCKING MASTER AUTOMATION  200/BL3924SB
     REVERSIBLE MASTER AUTOMATION  200/BL3924RB

  • Operational constraints:
    For gates with a maximum length of 3,5 m (5 m with a hinged arm
    and an obligatory electric locking device), maximum weight 400 kg.

    For the electric locks check the catalogue.

  • ARTICULATED/STRAIGHT ARM

     STANDARD HINGED OPERATOR ARM  206/BL324ARM
     in spray-painted cast aluminium





     HINGED OPERATOR ARM WITH JOINTS  206/BL324DRM
    in spray-painted cast aluminium
    for opening systems on slopes





     STRAIGHT ARM WITH SLIDING GUIDE  206/BL324DRM
    in spray-painted cast aluminium





     1000 MM GUIDE FOR SPECIAL OPENING REQUIREMENTS  206/BL3924GU2
    Supplied in lots of 2 pieces
     

  • 6-WIRE SPECIAL CONNECTING CABLE

     10 M CABLE  CABPC10
    (with end sleeves)

     100 M CABLE  CABPC100ST
    (supplied on a special spool)

HINGED/STRAIGHT ARM DIMENSIONS

TECHNICAL DATA

 OPERATOR ARM TECHNICAL SPECIFICATIONS

   
 Power supply  Vdc  24
 Electrical input  A  2
 Power input  W  50
 Duty cycle  %  70
 Opening time 90°  s  20 (16*)
 Maximum opening angle ° 130
 Maximum torque  Nm  300
 Protection grade  IP  44
     
* using a straight operator arm

 ELECTRONIC PROGRAMMER TECHNICAL SPECIFICATIONS

   
 Power supply  Vac  230
 Electrical input  A  1,2
 Maximum power yield  W  250
 Power output for 1 or 2 motors:  W  60 + 60
 Class device  Cls  II
     

 INCORPORATED RECEIVER CARD

   
 Reception frequency S449  MHz  433.92
 Number of channels  N°  4
 Number of functions  N°  2
 Number of stored codes  N°  300


INSTALLATION EXAMPLE


LEGEND

1 Geared motor (left) 
2 Geared motor (right)
3 Internal photocells
4 External photocells
5 Warning lights 
6 Mechanical selector switch
7 Electric locking device 
8 External aerial
9 All pole circuit breaker
10 Mains cable 230 Vac
11 Channelling for Cardin connection cable CABPC10
12 Channelling route for low voltage wires
13 Lateral protective photocells

Attention: The drawing is purely indicative and is supplied as a working base from which to choose the Cardin electronic components making up the installation. This drawing therefore does not lay down any obligations regarding the execution of the installation.

HINGED-ARM AUTOMATION FOR SWING-TO GATES


Motor power supply:
- 24 Vdc models
- 230 Vac models
Maximum gate weight 150 kg
Maximum opening angle 130°

BL1924 SERIES

Particularly suited for installations with oversize columns and where the opening direction of the gate is contrary to the position of the motor.
The system is made up of one or two operator arms managed by an external electronic programmer housed in a shockproof and waterproof container.
On the model BL1924ASW gate position is encoder controlled and self-programming thus reducing installation times to a minimum and optimising the programming procedure.
Repositioning takes place automatically whenever foreign objects get in the way of the gate as it is moving.
The electronic control unit is completed by the anti-crush and “soft start” and “soft stop” functions. The control electronics also comes complete with a display that monitors the programming stages and counts the number of manoeuvres carried out by the machine.
The operating parameters are set using dip-switches safely located inside the appliance.
Models with mechanical travel limits are available.
Both versions are fitted with a key-operated manual release mechanism.



Product DescriptionCode
  • ELECTROMECHANICAL OPERATOR WITH A 24 Vdc MOTOR

    Controlled by encoder.

    Electronic control unit to be ordered separately.

    SELF-LOCKING ELECTROMECHANICAL OPERATOR 200/BL1924ASW

  • ELECTROMECHANICAL OPERATOR WITH A 24 Vdc MOTOR

    With electronic travel limits.

    Electronic control unit to be ordered separately.

    SELF-LOCKING ELECTROMECHANICAL OPERATOR 200/BL1920

  • Operational constraints:
    For gates with a maximum length of 2 m,
    maximum weight 150 kg.

    For the electric locks turn to catalogue

  • ELECTRONIC PROGRAMMERS (FOR BL1924ASW)

    Programmer for the management of two encoder controlled motors.
    Mains power supply 230 Vac.
    Motor power supply 24 Vdc.
    Maximum motor power yield 250 W.
    Fitted with batteries, battery charger and an integrated S449 radio receiver module.
    For more information turn to catalogue

     ELECTRONIC PROGRAMMERS CC242ESSB

  • ELECTRONIC PROGRAMMERS (FOR BL1920)

    Programmer for the control of one motor.
    Mains power supply 230 Vac.
    Motor power supply 230 Vac.
    Maximum motor power yield 450 W.
    The programmer is factory set for the insertion of a Cardin standard receiver card.
     For more information turn to catalogue.

    ELECTRONIC PROGRAMMERS PRG807001

  • ELECTRONIC PROGRAMMERS (FOR BL1920)

    Programmer for the control of two motors. 

    Mains power supply 230 Vac. 

    Motor power supply 230 Vac. 

    Maximum power yield for two motors 470 + 470 W. 

    The programmer is factory set for the insertion of a Cardin standard receiver card.

    For more information turn to catalogue.


    ELECTRONIC PROGRAMMERS PRG807002

     

  • 6-WIRE SPECIAL CONNECTING CABLE

     10 m CABLE  CABPC10
    with end sleeves.

     100 m CABLE  CABPC100ST
    supplied on a special spool.

HINGED ARM DIMENSIONS

TECHNICAL DATA

 OPERATOR ARM TECHNICAL SPECIFICATIONS

 BL1924ASW

 Mains power supply  Vac  230
 Motor power supply  Vdc  24
 Electrical input  A  2
 Power input  W  60
 Duty cycle  %  70
 Opening time 90°  s  12,5
 Maximum opening angle °  130
 Torque  Nm  170
 Protection grade  IP  44


 OPERATOR ARM TECHNICAL SPECIFICATIONS

 BL1920

 Main power supply  Vac  230
 Motor power supply  Vdc  230
 Electrical input  A  1,3
 Power input  W  290
 Duty cycle  %  25
 Opening time 90°  s  15
 Torque  Nm  270
 Protection grade  IP  44


INSTALLATION EXAMPLE

LEGEND


1 Geared motor (left)
2 Geared motor (right)
3 Internal photocells
4 External photocells
5 Warning lights
6 Mechanical selector switch
7 Electric locking device
8 External aerial
9 All pole circuit breaker
10 Mains cable 230 Vac
11 Channelling for Cardin connection cable CABPC10
12 Channelling route for low voltage wires
13 Electronic programmer
14 Lateral protective photocells

Attention: The drawing is purely indicative and is supplied as a working base from which to choose the Cardin electronic components making up the installation. This drawing therefore does not lay down any obligations regarding the execution of the installation.

Realizzazione Sito Web Agency Attiva.it - Venezia