ELECTRONIC PROGRAMMERS

MAINS POWER SUPPLY 230 Vac
MOTOR OUTPUT 24 Vdc
PROTECTION GRADE IP55
FIREPROOFING GRADE V2
INCORPORATED RF DECODER S449 433 MHz
NiMH BATTERIES
“SOFT START” AND “SOFT STOP” FUNCTIONS
AUTOMATIC MOVEMENT PROGRAMMING

PRG 24V

Electronic devices for the control of automatic opening systems with one or two gate leaves: sliding gates, hinged gates and garage doors. powered by 24 Vdc they intelligently manage the movement of the gate.
Available in the following versions:
- with gate positioning control and encoder (CC242ESSB)
- with timer-controlled movement.
Both are equipped with an “S449” 433 MHz “FM” radio receiver card. Specially studied and designed for this type of use, these Cardin programmers are fitted with digital “step by step” time programming which is easily carried out in real time while the gate is moving thus reducing the installation time. The simplified programming method uses one or two buttons (depending on the version) allowing all functions to be programmed rapidly. The programming procedure is guided by a LED display.
The complete range of products have been designed and constructed in accordance with the safety standards in force and are fitted with all the connections needed to carry out an automatic installation.



Product DescriptionCode
  • ELECTRONIC PROGRAMMERS FOR THE MANAGEMENT OF ONE OR TWO ENCODER-CONTROLLED MOTORS

    Electronic programmer for encoder-controlled 24 Vdc motors that allow the precise position control of hinged gates. Monitoring the current consumption allows the control of a sophisticated anticrush safety system, and the “soft start” and “soft stop” functions reduce the stress on the mechanical components. Gate travel time programming is fully automatic and guided by a 6+digit display. Dip-switches allow you to set the system parameters including: the sequential button mode, automatic reclosing, warning lamp pre-flashing, intermittent warning lamp activation, indicator light and photoelectric cell function setting and electric lock enable. The six digit display allows you to visualise the number of manoeuvres carried out and to set several parameters such as the type of motor, the torque setting and the limited opening distance.


    Overall dimensions: 210 x 300 x 120


     ELECTRONIC CONTROL UNIT + BATTERY CHARGER AND BATTERIES  CC242ESSB

  • ELECTRONIC PROGRAMMERS FOR THE MANAGEMENT OF ONE OR TWO MOTORS

    Electronic programmer for the control of 24 Vdc hinged gates with intelligent time control functions that allow you to control the position of the gate.

    Monitoring the current consumption allows the control of a sophisticated anticrush safety system, and the “soft start” and “soft stop” functions reduce the stress on the mechanical components. Gate travel time programming is fully automatic and guided by a 6+digit display. Dip-switches allow you to set the system parameters including: the sequential button mode, automatic reclosing, warning lamp pre-flashing, intermittent warning lamp activation, indicator light and photoelectric cell function setting and electric lock enable. The six digit display allows you to visualise the number of manoeuvres carried out and to set several parameters such as the type of motor, the torque setting and the limited opening distance.


    Overall dimensions: 210 x 300 x 120


     ELECTRONIC CONTROL UNIT, BASIC VERSION  PRG900

     ELECTRONIC CONTROL UNIT + BATTERY CHARGER AND BATTERIES  PRG900CB

     VOLTAGE REGULATOR STABILIZED AT 24 Vdc  SELINTCV
    The device supplies a regulated 24 Vdc voltage in output starting from a direct current input that can vary from 19 Vdc to 38 Vdc. It is fitted with 2 signal LEDs, one indicating the presence of voltage at the output binding post and the other giving status information (correct operation, overload, activated protection).

     KIT BATTERY CHARGER + NIMH BATTERIES  KBNIMH-1
    Allows the programmer PRG900 to work during blackouts.

ELECTRONIC PROGRAMMERS

MAINS POWER SUPPLY 230 Vac
MOTOR OUTPUT 230 Vac
PROTECTION GRADE IP55
FIREPROOFING GRADE V2
INTERFACE FOR A STANDARD SLOT-IN RADIO CARD
COMMAND INPUTS: TA, TC, TD, TB.

PRG 230V

Electronic devices for the control of automatic opening systems. Specially studied and designed for this type of use, these Cardin programmers are fitted with digital “step by step” time programming which is easily carried out in real time while the gate is moving thus reducing the installation time.
The simplified programming method uses one or two buttons (depending on the version) allowing all functions to be programmed rapidly. In the double gate/door version the programming procedure is guided by a LED display.
The complete range of products have been designed and constructed in accordance with the safety standards in force and feature automatic, semi-automatic, manual and remote control functions (the product takes a Cardin standard slot-in receiver card).
Electronic devices for the control of automatic opening systems with one or two gate leaves: sliding gates, hinged gates and garage doors powered by 230 Vac.
The complete range of programmers simplifies and solves all possible installation problems. The high product-quality level together with accurate design and a selective choice of materials allows trouble free operation and maximum reliability under all kinds of working conditions.



Product DescriptionCode
  • ELECTRONIC PROGRAMMERS FOR THE CONTROL OF ONE 230V MOTOR WITH MAXIMUM POWER YIELD 650 W

    Digital work time control. Command inputs: TA, TC and TB. Security inputs: photocells, safety edge (N.C. contact or 8.2 kΩ), digital safety edge. 

    Output for a courtesy light 230 Vac 300 W and for a mollight warning light. The appliance is supplied with a “S449”, 433 MHz, “FM” decoder.

    (complete with cable glands Ø 3 x Ø9 mm + Ø 1 x Ø16 mm)


    Use

    Suitable for the control of automatic rolling shutters.


    Overall dimensions: 135 x 175 x 85


     ELECTRONIC CONTROL UNIT, BASIC VERSION  PRG304E

     ELECTRONIC PROGRAMMER WITH EXTERNAL CONTROL BUTTONS  PRG304ETC

  • ELECTRONIC PROGRAMMERS FOR THE CONTROL OF ONE 230V MOTOR WITH MAXIMUM POWER YIELD 600 W

    Digital work time control. Possible operation without mechanical travel limits. Command inputs: TA, TC, TD, TB. The appliance is fitted with an interface for the insertion of a standard Cardin radio receiver card.

    (complete with cable glands Ø 2 x Ø9 mm + Ø 2 x Ø16 mm)


    Use

    Suitable for the control of automatic road barriers.


    Overall dimensions: 135 x 175 x 85


     ELECTRONIC PROGRAMMER  PRG302E

     SLOT-IN CARD  YPR302SR2
    Slot-in card that allows the complete control of the opening and closing micro-switches as well as the control of the inverting photocells (for application on 230V road barriers).

  • ELECTRONIC PROGRAMMERS FOR THE CONTROL OF ONE 230V MOTOR WITH MAXIMUM POWER YIELD 450 W

    Digital work time control. Possible operation without mechanical travel limits. Torque setting. Maximum power initial thrust control and torque limitation. The appliance is fitted with an interface for the insertion of a standard Cardin radio receiver card.


    Use

    Suitable for the control of automatic gates and doors with one 230V motor.


    Overall dimensions: 210 x 300 x 105


     ELECTRONIC PROGRAMMER  PRG807001

  • ELECTRONIC PROGRAMMERS FOR THE CONTROL OF TWO 230V MOTORS WITH MAXIMUM POWER YIELD 470 + 470 W

    Digital work time control separately memorised for each gate leaf. Possible operation without mechanical travel limits. Torque setting. 

    Maximum power initial thrust control and torque limitation. The appliance is fitted with an interface for the insertion of a standard Cardin radio receiver card.


    Use

    Suitable for the control of automatic gates and doors with two 230V motors.


    Overall dimensions: 210 x 300 x 105


     ELECTRONIC PROGRAMMER  PRG811002

     ADDITIONAL FUNCTION CARD  SELSLC
    Optional card that allows you to extend the functions of the control units:
    - Timer-controlled lamp 230Vac - 500W (electric lock or an electric brake can be fitted as an alternative);
    - 8,2 kΩ safety edge management.

  • CABLE GLANDS KIT

     CABLE GLANDS KIT  XSL4DIE09960
    Cable glands4 x Ø16 mm. 
    For PRG807001 e PRG811002

ELECTRONIC PROGRAMMERS

MAINS POWER SUPPLY 230 Vac / 400 Vac
MOTOR OUTPUT:
SINGLE PHASE 230 Vac
THREE PHASE 400 V3~.
PROTECTION GRADE IP55
FIREPROOFING GRADE V2
INTERFACE FOR A STANDARD SLOT-IN RADIO CARD
COMMAND INPUTS: TA, TC, TD, TB.

SINGLE- THREEPHASE

Electronic devices for the control of automatic opening systems. The appliances feature integrated logic and function activation confirmation using leds.
The complete range of products have been designed and constructed in accordance with the safety standards in force and feature automatic, semi-automatic, manual and remote control functions.
The appliances can take a Cardin standard slot-in receiver card and are supplied with cable glands.
Electronic devices for the control of automatic opening systems with one gate leaf: sliding gates, hinged gates, garage doors and factory doors.
The high product-quality level together with accurate design and a selective choice of materials allows trouble free operation and maximum reliability under all kinds of working conditions.



Product DescriptionCode
  • INDUSTRIAL PROGRAMMER CONTROLLING ONE SINGLE PHASE/THREE PHASE MOTOR

    - 370 W Single phase power supply 230 Vac,

    - 700 W Three phase power supply 400 V3~.

    Automatic, semiautomatic, manual and remote control functions.

    Command inputs TA, TB, TC, TD, TAL.

    Incorporated door security switch.

    Optional external control buttons.

    Electric brake output.

    Interface for a standard slot-in radio receiver card.

    Supplied with 4 x Ø16 mm cable glands.


    Use

    Suitable for the control of industrial gates and doors with one single-phase/three phase motor.


    Overall dimensions: 175 x 265 x 105


     ELECTRONIC CONTROL UNIT, BASIC VERSION  PRG3830CE

     ELECTRONIC PROGRAMMERS WITH EXTERNAL CONTROL BUTTONS  PRG383TCE

  • INDUSTRIAL PROGRAMMER CONTROLLING ONE THREE PHASE MOTOR

    - 2200 W Three phase power supply 400 V3~.

    Automatic, semiautomatic, manual and remote control functions.

    Command inputs TA, TB, TC, TD, TAL.

    Incorporated door security switch.

    Optional external control buttons.

    Electric brake output.

    Interface for a standard slot-in radio receiver card.

    Supplied with 4 x Ø16 mm cable glands.


    Use

    Suitable for the control of industrial gates and doors with one three phase motor.


    Overall dimensions: 175 x 265 x 105


     ELECTRONIC CONTROL UNIT, BASIC VERSION  PRG3840CE

     ELECTRONIC PROGRAMMERS WITH EXTERNAL CONTROL BUTTONS  PRG384TCE

  • INDUSTRIAL PROGRAMMERS WITH SEPARATE LOGIC CARDS, FOR THE INDEPENDENT CONTROL OF ONE OR TWO SINGLE-PHASE MOTORS

    - 470 + 470 W Single phase power supply 230 Vac.

    Automatic, semiautomatic, manual and remote control functions. 

    Command inputs TA, TB, TC, TD, TAL.

    Incorporated door security switch.

    Optional external control buttons.

    Double opening/closing travel limits.

    Interface for a standard slot-in radio receiver card.

    Supplied with 4 x Ø16 mm cable glands.


    Use

    Suitable for the control of industrial gates and doors with two 230V motors with separate logic control.


    Overall dimensions: 175 x 265 x 105


     

     ELECTRONIC PROGRAMMERS WITH SEPARATE LOGIC CARDS  PRGHRM2CE


Realizzazione Sito Web Agency Attiva.it - Venezia