INFRARED BARRIERS

RECEIVER POWER SUPPLY 12/24 Vac-dc
PROJECTOR POWER SUPPLY 3V WITH A LITHIUM BATTERY.
MAXIMUM RANGE 12 METRES
PROTECTION GRADE IP55

CDRX12

CDRX12is a next generation infrared safety system, particularly suited to the protection of passageways (traffic and pedestrian) that are fitted with automatic opening and closing systems. The electronic circuit respects the most up to date standards and regulations and conforms to the standard 3 of the UNI EN 13849-1 (update of the EN954-1). It is possible to connect up to 3 pairs of photocells and synchronise the transmission (multiplex system).The necessity of guaranteeing greater ambient noise immunity has led to the evolution of both the transmitter and receiver cards. The system is based on the criteria “resistance to single failure” that guarantees the maintenance of safety in case of electrical problems.
The receiver should be installed close to the electronic programmer and wired up drawing its 12/24V power supply directly from the programmer while the projector can be installed on any surface and doesn’t require wiring. Power is supplied by a solar panel when light is present and by a 3V lithium battery when insufficient light is available. The batteries lifespan can be optimised by setting the energy saving function and varying the cut-in time and the installation distance between the two photoelectric cells.

Technical description
Infrared transmission by means of digital modulation of the carrier signal Reception via demodulation and decoding of the protocol allowing the transmitter to be identified. Self-locking adjustable lens which can be rotated horizontally through 90° and vertically through plus or minus 30° with respect to the standard installation position.
Double relays on the receiver with digital control increase the security and safety level of the output part (the part that furnishes the at rest/alarm signal)
Selection ofthe output contact mode (potential free or resistance 8, 2 kΩ contacts). Differentiated signal LEDS on the receiver indicate the “correct function” status by flashing briefly (every minute) or the “alarm” status when they remain constantly lit.
Pre-amplified receiver lens.
Reinforced power supply allowing voltages up to 40 Vdc or 28 Vac.
Overall dimensions: 60 x 125 x 41.



Product DescriptionCode
  • PAIR OF SURAFACE MOUNT PHOTOELECTRIC CELLS, RANGE 12 M

     PAIR OF SURAFACE MOUNT PHOTOELECTRIC CELLS, RANGE 12 M  CDRX12

    The kit contains:
    - 1 projector + battery pack;
    - 1 receiver;
    - 1 cablegland;
    - assorted screws.

INFRARED BARRIERS

POWER SUPPLY 12/24 Vac-dc
MAXIMUM RANGE 15 METRES
CONFORMS TO THE SAFETY DIRECTIVES EN12978 IN CATEGORY
3 OF THE EN ISO 13849-1 AND CATEGORY 2 OF THE EN61496-2
CDR 973 AX anti-tamper aluminium box IP66.
CDR 973 EX shock-proof in a plastic box.
CDR 973 IX shock-proof plastic embedding case.

CDR973

CDR 973 is a specifically designed range of next generation infrared security devices for the protection of carriageways and pedestrian passageways fitted with automatic opening and closing systems: it is an extremely valid safety system that respects the requirements of the standard EN 12978. The appliance is fitted with a new optical transmission system (conforms to the specifications indicated by part 2 of the European law IEC 61496-2) that respects an infrared opening angle of +/- 5°. The management of both the transmitter part and the receiver part is carried out by micro controller, giving the advantage of greater precision in the generation of impulses transmitted via infrared and this (once modulated according to a digital protocol that allows information transfer from the transmitter to the receiver) eliminates the risk of blinding caused by other infrared systems working on the same frequency and located in the vicinity. This is a superior class appliance that will be available in three different containers in order to solve all installation requirements.

Technical description
Infrared emission obtained by digital modulation of the carrier signal.
Reception with protocol demodulation and decoding allowing the transmitter to be recognised.
It is possible to connect up to 3 pairs of photocells and synchronize the transmission (multiplex system) without interference; selection is carried out by means of a three-way dip-switch located on the transmitter and the receiver and by interconnecting the three transmitters using a two-wire cable (synchronism). The receiver does not require any other form of interconnection.
Digitally controlled double relays are situated on the receiver card in order to increase the safety of the appliance (at rest/alarm status control).
Jumper for selecting the output contact mode (potential free or resistance 8, 2 kΩ contacts).
Drop out delay selection via dip-switch (0, 2 seconds or 3 seconds).
High intensity LED (on the receiver) facilitating lens centring from a certain distance.
2 indicator LEDs on the receiver:
- green - when lit indicates the photoelectric cell is at rest;
- red - when lit indicates the photoelectric cell is in alarm, when flashing indicates photoelectric cell failure.
Pre-amplified receiver lens.
Reinforced power supply tolerating voltages up to 40 Vdc or 28 Vac.



Product DescriptionCode
  • PAIR OF CLASS 3 PHOTOELECTRIC CELLS IN AN ALUMINIUM CASE

    Maximum range 15 m

    Power supply 12/24 Vac-dc

    Protection grade IP66

    Transmitter and receiver housed in a compact waterproof aluminium case. Self locking adjustable lens which can be rotated horizontally through 90° and vertically through plus or minus 30° with respect to the standard installation position. Double-relay with serial exchange. 

    It is possible to connect up to 3 pairs of photocells and synchronize the transmission (multiplex system).


    The kit contains:

    - 1 projector in an aluminium case;

    - 1 receiver in an aluminium case;

    - 2 pipe glands;

    - assorted screws.


    Overall dimensions:  56 x 142 x 63


     PAIR OF PHOTOELECTRIC CELLS IN AN ALUMINIUM CASE, RANGE 15 m  CDR973AX

  • PAIR OF CLASS 3 PHOTOELECTRIC CELLS

    Maximum range 15 m

    Power supply 12/24 Vac-dc

    Protection grade IP55

    Transmitter and receiver housed in a waterproof plastic case. Self locking adjustable lens which can be rotated horizontally through 90° and vertically through plus or minus 30° with respect to the standard installation position. Double-relay with serial exchange.

    It is possible to connect up to 3 pairs of photocells and synchronize the transmission (multiplex system).


     PAIR OF FLUSH-FITTING PHOTOELECTRIC CELLS, RANGE 15 15 m  CDR973IX
    The kit contains:
    - 1 projector;
    - 1 receiver;
    - 2 embedding cases;
    - 2 lens covers for flush-fitting photoelectric cells;
    - assorted screws and gaskets.
    Overall dimensions 50 x 90 x 60

     PAIR OF SURFACE-MOUNT PHOTOELECTRIC CELLS, RANGE 15 m  CDR973EX
    The kit contains:
    - 1 projector;
    - 1 receiver;
    - 2 lens covers for surface-mount photoelectric cells;
    - 2 fast-fitting wall brackets;
    - assorted screws and gaskets.
    Overall dimensions 50 x 90 x 60

INFRARED BARRIERS

POWER SUPPLY 12/24 Vac-dc
MAXIMUM RANGE 60 METRES
OPERATING TEMPERATURE RANGE -10..+55 °C
CDR 841 shock-proof, plastic case IP55 for flush-fitting and surface mounting. Maximum range 15 m.
CDR 851 shock-proof, plastic case IP55 for surface mounting. Maximum range 60 m.
CDR 842A anti-tamper aluminium case IP66. Maximum range 15 m.
CDR 852A anti-tamper aluminium case IP66. Maximum range 60 m.

CDR851

Modulated infrared barrier consisting of a transmitter and a receiver. It constitutes an efficient safety system for the protection of passageways or spaces which are equipped with automatic doors or gates.
A designer case, pleasing on the eye, encloses innovative technical solutions which make the system extremely reliable under all working conditions.
Self-locking adjustable lens which can be rotated horizontally through 90° and vertically through plus or minus 30° with respect to the standard installation position. These adjustments permit lateral fitting and installations where the transmitter and receiver are at different heights.
Double-relay with serial exchange as required by the local standards and regulations in force.
The device is extremely easy to install both for the surface-mounting version as well as for the embedding version.
The vast range of available models meets all possible system requirements.



Product DescriptionCode
  • PAIR OF PHOTOELECTRIC CELLS IN AN ALUMINIUM CASE CDR842A-852A

    Range 15 m - 60 m

    Power supply 12/24 Vac-dc

    Protection grade IP66

    Transmitter and receiver housed in a waterproof plastic case.

    Self locking adjustable lens which can be rotated horizontally through 90° and vertically through plus or minus 30° with respect to the standard installation position.

    Double-relay with serial exchange. 

    Sensitivity adjustment trimmer located on the receiver (only CDR852A).


    The kit contains:

    - 1 projector in an aluminium box;

    - 1 receiver in an aluminium box;

    - 2 pipe glands;

    - assorted screws.


    Overall dimensions: 56 x 142 x 63


     PAIR OF PHOTOELECTRIC CELLS IN AN ALUMINIUM CASE, RANGE 15 m  CDR842A

     PAIR OF PHOTOELECTRIC CELLS IN AN ALUMINIUM CASE, RANGE 60 m  CDR852A

  • PAIR OF PHOTOELECTRIC CELLS CDR841-851

    Range 15 m - 60 m

    Power supply 12/24 Vac-dc

    Protection grade IP55

    Transmitter and receiver housed in a waterproof plastic case.

    Self locking adjustable lens which can be rotated horizontally through 90° and vertically through plus or minus 30° with respect to the standard installation position.

    Double-relay with serial exchange. 

    Sensitivity adjustment trimmer located on the receiver (only CDR851).


     PAIR OF FLUSH-FITTING PHOTOELECTRIC CELLS, RANGE MAX. 15 m  CDR841I00
    The kit contains:
    - 1 projector;
    - 1 receiver;
    - 2 embedding cases;
    - 2 lens covers for flush-fitting photoelectric cells;
    - assorted screws and gaskets.
    Overall dimensions: 50 x 90 x 60

     PAIR OF SURFACE-MOUNT PHOTOELECTRIC CELLS, RANGE MAX. 15 m  CDR841E00

     PAIR OF SURFACE-MOUNT PHOTOELECTRIC CELLS, RANGE MAX. 60 m  CDR851

     PAIR OF SURFACE-MOUNT PHOTOELECTRIC CELLS, RANGE MAX.15 m  CDR851T
    Anti-tamper version.

     PAIR OF SURFACE-MOUNT PHOTOELECTRIC CELLS, RANGE MAX. 15 m  CDR851R
    Delayed version - 5 s not adjustable
    The kits contain:
    - 1 projector;
    - 1 receiver;
    - 2 lens covers for surface-mount photoelectric cells;
    - 2 fast-fitting wall brackets;
    - assorted screws and gaskets.
    Overall dimensions: 50 x 90 x 60

INFRARED BARRIERS

POWER SUPPLY 12/24 Vac-dc
MAXIMUM RANGE 10 METRES
PROTECTION GRADE IP55
OPERATING TEMPERATURE RANGE -10..+55 °C

CDR999

CDR999 is a next generation infrared safety system, particularly suited to the protection of passageways (traffic and pedestrian) that are fitted with automatic opening and closing systems. The electronic circuit respects the most up to date standards and regulations and conforms to the standard 3 of the UNI EN 13849-1 (update of the EN954-1). It is possible to connect up to 3 pairs of photocells and synchronise the transmission (multiplex system).
The necessity of guaranteeing greater ambient noise immunity has led to the evolution of both the transmitter and receiver cards. The system is based on the criteria “resistance to single failure” that guarantees the maintenance of safety in case of electrical problems.
The management of both the transmitter part as well as the receiver part is carried out by means of a microcontroller, giving the advantage of greater precision when generating the impulses transmitted via infrared that are modulated using a digital protocol thus eliminating the risk of blackout spots.

Technical description
Infrared transmission by means of digital modulation of the carrier signal Reception via demodulation and decoding of the protocol allowing the transmitter to be identified.
The possibility of connecting 3 devices in an array therefore multiplexing the transmission without interference. The selection is made by means of a two-way dip-switch located on both the transmitter and the receiver that allows you to connect the transmitters together via a two-way cable (synchronism); no ulterior connection is required for the receiver. Double relays on the receiver with digital control increase the security and safety level of the output part (the part that furnishes the at rest/alarm signal)
Jumper for selecting the output contact mode (potential free or resistance 8, 2 kΩ contacts). Differentiated signal LEDS on the receiver indicate the “correct function” status by flashing briefly (every minute) or the “alarm” status when they remain constantly lit.
Pre-amplified receiver lens.
Reinforced power supply allowing voltages up to 40 Vdc or 28 Vac.
Overall dimensions: 50 x 90 x 40.

The kit contains:
- 1 projector;
- 1 receiver;
- assorted gaskets;
- assorted screws.

Lots of 5 pieces



INFRARED BARRIERS

POWER SUPPLY 12/24 Vac-dc
MAXIMUM RANGE 10 METRES
PROTECTION GRADE IP54
OPERATING TEMPERATURE RANGE -10..+55 °C

CDR861

The infrared barrier constitutes an efficient safety system for the protection of passageways or spaces which are equipped with automatic door or gate systems, and for the detection and control of general passageways, whether carriageway or pedestrian, situated inside or outside buildings.

Technical description
The projector and receiver are housed in a compact, shock-proof plastic casing. The casing is designed to be surface mounted on walls. The ease of installation is complemented by the rapid adjustment time: centring is carried out, without having to loosen or fasten any screws. Just align the devices on the same axis.
The system of diodes (sender - receiver), fitted with a constraint guide for the infrared beam remains in a fixed position.
Base in thermoplastic rubber.
Lens cover with holding gasket.
Double-relay with serial exchange as required by the local standards and regulations in force.
Protection grade IP54.
Fireproofing grade V0.
Overall dimensions: 65 x 92 x 22.

The kit contains:
- 1 projector;
- 1 receiver;
- assorted gaskets;
- assorted screws.

Lots of 10 pieces



INFRARED BARRIERS

POWER SUPPLY 12/24 Vac-dc
RANGE FROM 1 TO 15 METRES
PROTECTION GRADE (SENSORS) IP55
CONFORMS TO THE SAFETY DIRECTIVES EN12978 IN CATEGORY 3 OF THE EN ISO 13849-1 AND CATEGORY 2 OF THE EN61496-2
CDR 892C3 Dual-beam multiplex infrared barrier.
FTR 893C3 Single-beam infrared barrier.
CDR 891 Single-beam infrared barrier mounted on a rail guide DIN 46277.

CDR891 -892 -893

Suitable for the protection of passageways or spaces which are equipped with automatic installations such as lifts and automatic doors or where you wish to detect or count the passage of people or things while using the least possible space.
The infrared barriers with mini sensors are ideal for installations that need to be discreet but at the same time require the passageway to be safely and reliably protected.
The electronic circuit respects the most up to date standards and regulations and conforms to the standard 3 of the UNI EN 13849-1 (update of the EN954-1). The necessity of guaranteeing greater ambient noise immunity has led to the evolution of both the transmitter and receiver cards. The system is based on the criteria “resistance to single failure” that guarantees the maintenance of safety in case of electrical problems.
The management of both the transmitter part as well as the receiver part is carried out by means of a microcontroller, giving the advantage of greater precision when generating the impulses transmitted via infrared that are modulated using a digital protocol thus eliminating the risk of blackout spots.

Technical description
Infrared transmission by means of digital modulation of the carrier signal.
Possibility to adjust the power of the projector by setting a jumper to one of the three available levels depending on the range that needs to be covered.
Double relays on the receiver with digital control increase the security and safety level of the output part (the part that furnishes the at rest/alarm signal).
Jumper for selecting the output contact mode (potential free or resistance 8, 2 kΩ contacts).
Jumper for selecting the number of active beams (only in the dual beam model).



Product DescriptionCode
  • DUAL-BEAM MULTIPLEX INFRARED BARRIER IN CLASS 3

    Overall dimensions 90 x 50 x 20


     DOUBLE-RELAY INFRARED BARRIER  CDR892C3
    Power supply 12/24 Vac-dc
    Range: 15 m indoors - 10 m outdoors
    Transmitter cable 5 m - Receiver cable 3 m

     DOUBLE-RELAY INFRARED BARRIER  CDR892C3-1
    Power supply 12/24 Vac-dc
    Range: 15 m indoors - 10 m outdoors
    Transmitter cable 10 m - Receiver cable 7 m

     DOUBLE-RELAY INFRARED BARRIER  CDR892C3-2
    Power supply 12/24 Vac-dc
    Range: 15 m indoors - 10 m outdoors
    Transmitter cable 15 m - Receiver cable 10 m

  • SINGLE-BEAM INFRARED BARRIER CLASS 3

    Overall dimensions 90 x 50 x 20


     DOUBLE-RELAY INFRARED BARRIER  FTR893C3
    Power supply 12/24 Vac-dc
    Range: 2,5 m indoors
    Transmitter cable 4 m - Receiver cable 4 m

  • SINGLE-BEAM INFRARED BARRIER (APPLIANCE NOT IN CLASS 3)

    with a socket for mounting on a rail guide DIN 46277.  

    Overall dimensions 60 x 45 x 117


     DOUBLE-RELAY INFRARED BARRIER  CDR891
    Power supply 12/24 Vac-dc
    Range: 8 m indoors - 6 m outdoors
    Transmitter cable 5 m - Receiver cable 3 m

     DOUBLE-RELAY INFRARED BARRIER  CDR891-1
    Power supply 12/24 Vac-dc
    Range: 8 m indoors - 6 m outdoors
    Transmitter cable 15 m - Receiver cable 10 m

     DOUBLE-RELAY INFRARED BARRIER  CDR893
    Power supply 12/24 Vac-dc
    Range: 4 m indoors -2 m outdoors
    Transmitter cable 3 m - Receiver cable 3 m


Realizzazione Sito Web Agency Attiva.it - Venezia